short-circuiting

英 [ˌʃɔːt ˈsɜːkɪtɪŋ]

美 [ˌʃɔːrt ˈsɜːrkɪtɪŋ]

v.  (使)短路; (做事)抄近路，走捷径
short-circuit的现在分词

柯林斯词典

• V-ERG (使)短路
  If an electrical deviceshort-circuitsor if someone or somethingshort-circuitsit, a wrong connection or damaged wire causes electricity to travel along the wrong route and damage the device.
  1. Carbon dust and oil build up in large motors and cause them to short-circuit...
     碳尘和燃油在大发动机里越积越多，造成了发动机短路。
  2. Once inside they short-circuited the electronic security.
     一旦置入，它们就会使电子安全设施短路。
  3. Short-circuitis also a noun.
     
  4. The fire was started by an electrical short-circuit.
     火灾是由电线短路引发的。
• VERB 回避，绕过（某一流程或程序)
  If someone or somethingshort-circuitsa process or system, they avoid long or difficult parts of it and use a quicker, more direct method to achieve their aim.
  1. The approach was intended to short-circuit normal complaints procedures.
     这种方法旨在避开正常的投诉程序。

双语例句

• Computer simulation on arc welding short-circuiting transfer process and current waveform control
  弧焊短路过渡过程及其电流波形控制的计算机仿真
• The rule of the arc-time and short-circuiting transfer cycle time under the high speed welding was researched by welding quality analyzer of Hannover.
  采用汉诺威焊接质量分析仪，研究了在高速焊接的情况下，燃弧时间与短路过渡周期的变化规律。
• Parallel-style Waveform Control on Welding Arc in Droplet Short-circuiting Transfer Process of CO_2 Arc Welding
  CO2弧焊熔滴过渡过程焊接电弧的并联式波形控制
• Adaptive control system with constant frequency of droplet transfer for waveform controlled short-circuiting co_2 arc welding
  波控短路过渡CO2焊接恒频自适应控制系统
• The short-circuiting transfer is a main form of CO2 arc welding droplet transfer. The arc welding short-circuiting transfer process and the current waveform control process of a developed new type waveform controller a simulated.
  对CO2弧焊短路过渡过程，以及研制的一种新型波控器的电流波形控制过程进行了计算机模拟仿真，仿真结果与实验吻合。
• Otherwise, accidental short-circuiting can lead to electric shock and to serious damage.
  否则，意外的短路可能引起触电和严重的损坏。
• The effects of the short-circuiting transfer parameters on weld formation quality in high speed CO2 welding process were analyzed.
  分析了高速CO2焊接过程中短路过渡参数对焊缝成形质量的影响。
• The Employer reserves the right to perform additional inspection of production welds made using GMAW in the short-circuiting transfer mode.
  业主保留对使用短路过渡模式下的gmaw的生产焊缝进行附加检验的权利。
• Short-circuiting Effect and the Solution in Gnutella Network
  Gnutella网络中的短路效应及其解决方案
• The CO2 welding process needs the special external characteristic and dynamic characteristic of power source for there are alternately arcing time and short circuiting time at the period of short-circuiting CO2 welding.
  在采用短路过渡方式的CO2焊过程中，短路和燃弧过程交替发生，因此它对电源的外特性和动特性有特殊的要求。